Sea gull lighting 5232-02 Installation Guide download pdf

Install canopy loop (E) on canopy (G) with lockwasher (Q) and nut (B).

(Note: Loop may be factory installed.).

STEP 1:

To replace glass, bend upper and lower tabs in corners of glass to be

replaced. Install glass up through bottom of fixture. Bend tabs back

as before.

REPLACING GLASS

Installation And Safety Instructions

Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to

this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________

HC-264

81409

• Be sure the electricity to the system you are working on is turned

off; either the fuse removed or the circuit breaker set at off.

• Use of other manufacturers components will void warranty, listing

and create a potential safety hazard.

• If you are unclear as to how to proceed, contact a qualified

electrician.

• You don’t need special tools to install this fixture.

• Be sure to follow the steps in the order given.

• Under no circumstances should a fixture be hung on house

electrical wires, nor should a swag type fixture be installed on a

ceiling which contains a radiant type heating system.

• Read instructions carefully.

•

Save these instructions.

IMPORTANT SAFETY INSTRUCTIONS

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.

Do not use abrasive materials such as scouring pads or powders,

steel wool or abrasive paper.

Keep this sheet for future reference, and in case you need to order

replacement parts. Parts for this fixture can be ordered from place

of purchase. Be sure to use exact wording from illustration when

ordering parts.

CLEANING

ORDERING PARTS

Carefully remove the fixture from the carton and check that all parts

are included, as shown in Figure 1. Be careful not to misplace any of

the scr

ews or parts which are needed to install this fixtur

BEFORE YOU BEGIN

FOR CHAIN HUNG (FIG. 1)

Install lock washer (Q), nipple (C) and fixture loop (J), in that or

der

, on

coupling (M).

STEP 2:

OUTLET BOX

*WIRE

*CONNECTORS

CANOPY (G)

CANOPY

LOOP (E)

MOUNTING

SCREWS (I)

CHAIN (N)

NUT (B)

FIXTURE

LOOP (J)

CENTER

PIPE (P)

FIGURE 1 *NOT SUPPLIED

FOR CHAIN HUNG

GROUNDING

AND

MOUNTING

BAR

LOCK UP

GREEN GROUNDING SCREW (D)

*OUTLET

*BOX

SCREWS

MOUNTING

BAR (A)

*WIRE

CONNECTORS

MOUNTING

SCREWS (I)

*GROUND

*WIRE

*OUTLET

*BOX

FIGURE 2

*NO

T INCLUDED

FIXTURE

CAGE (O)

CAP NUTS (F)

COUPLING (M)

CANDLE

COVER (T)

Insert fixtur

e assembly thr

ough canopy (G). Secur

e in place with lock

washer (Q) and nut (B).

STEP 2: FOR FLUSH MOUNT (IF APPLICABLE) (FIG. 3)

Install nipple (C) onto coupling (M) (if applicable).

STEP 3:

1 2

FOR FLUSH MOUNT 2

Summary of Contents

Page 1

Install canopy loop (E) on canopy (G) with lockwasher (Q) and nut (B).(Note: Loop may be factory installed.). STEP 1:To replace glass, bend upper and

Page 2 - FOR FLUSH MOUNT

After wires are connected, tuck them carefully inside outlet box andthen raise the canopy (G) against ceiling allowing for mountingscrews (I) to protr

Comments to this Manuals

No comments

Sea gull lighting 5232-02 Installation Guide

Browse online or download Installation Guide for Unknown Sea gull lighting 5232-02. Sea Gull Lighting 5232-02 Installation Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Sea gull lighting 5232-02