INSTALLATION HC-1156
FINAL ASSEMBLY
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
Thread fixture mounting screws (F) in through top of mounting bar
(
A) (raised side is on top, as illustrated). Run screw threads all the
way down to the heads. Secure mounting bar (A) to outlet box with
outlet box screws (not supplied).
Using 2 pairs of pliers, open one link of chain (S) and connect it to
the fixture loop (B) at the top of the fixture. Slide screw collar ring (L)
and canopy (O) to top of fixture.
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 4:
Open one link on the other end of the chain (S) and attach it to
the canopy loop (E).
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box.
DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
WHITE
*
P
ARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
CLEANING
ORDERING PARTS
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
STEP 1: (FLUSH MOUNT)
After wires are connected, tuck them carefully inside outlet box and
then raise the fixture canopy (I) against ceiling allowing for mounting
screws (F) to protrude through holes in fixture canopy (I). Secure in
place with cap nuts (J).
Make sure no bare wires can be seen outside wire connectors.
STEP 4:
Raise shade (M) over center pipe (P). Secure in place by threading
bottom lockwasher and hexnut (Z) and finial (N).
STEP 3:
Install lamp(s).
STEP 1: FLUSH MOUNT
FOR CHAIN HUNG ONLY (STEPS 2-4)
WIRING INSTRUCTIONS
STEP 3:
Secure mounting bar (A) to outlet box using outlet box screws.
Thread nut (G) onto nipple (C) so five threads are exposed. Thread
nipple (C) into mounting bar (A) and secure by tightening nut (G).
Thread screw collar (H) to nipple (C).
STEP 2:
D. Gently try to remove the wires from the connector, If you can
remove the wires,, carefully re-do steps B and C, as above and
c
heck again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
The green grounding screw (D) is to be inserted into the hole with
two raised dimples provided on the mounting bar (A). Wrap the ground
w
ire from the fixture (if supplied) and the ground wire from the outlet
box (bare metal or green insulated wire) around the green
grounding screw (D) on the mounting bar (A) if uninsulated wire is
o
n the mounting bar (A), connect the ground wire from the fixture
(if supplied) and the outlet box to it using a small wire connector
(not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
GROUNDING INSTRUCTIONS:
STEP 2: (CHAIN HUNG)
Raise canopy (O) to ceiling and secure by threading screw collar
ring (L) to screw collar (H).
(1 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals