Sea gull lighting 9858-962 Installation Guide download pdf

ARNING:

E SURE THE ELECTRICITY TO THE WIRES YOU ARE

WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED OR THE

IRCUIT BREAKER OFF.

RISK OF FIRE: Exceeding maximum wattage may result in over-heating

onductors. Read instructions carefully. If you are unclear as to how to

proceed, consult a qualified electrician.

CAUTION: RISK OF FIRE. Use only 12V lamps with 12V systems.

Use of 12V lamps with 24V system may result in damage to the

system and surrounding area.

CAUTION: RISK OF FIRE. Must use Sea Gull No. 9488 fused plug if

used with transformers over 60w at 12 volts or 100w at 24 volts.

(USE ONLY WITH AMBIANCE 105˚ CABLE)

1. Secure surface mount ring to surface

by marking hole location on surface

and screw surface mount ring to

surface making sure surface mount ring does not flex out of round.

2. Drill wire exit hole in surface or run wire thru notch in surface mount ring.

3. Line up retaining springs on fixture housing with grooves in surface

mount ring and press fixture housing into surface mount ring.

1. Drill a 2 3/4” dia. hole in surface.

2. Press fixture housing into

2 3/4” dia. hole.

SURFACE MOUNTING

INSTALLATION AND SAFETY INSTRUCTIONS HC-207

FOR YOUR SAFETY

FUSED PLUG INST

ALLATION (NOT INCLUDED)

TRIM INSTALLATION

RECESS MOUNTING

NOT INCLUDED

TRIM

1/8”

HOOKS (2)

SLOTS (4)

RETAINING SPRING (2)

SURFACE

MOUNT

RING

SCREWS (2)

GROOVES (2)

HOLES (2)

NOTCH

FIXTURE

HOUSING

Lamp

031606

1. Cut wire to desired length.

2. Split ends of wire about (1/2”) and insert each end of the wire

as far as possible into the plug. Do not strip any insulation off

the wire.

3. Insert contact into one end of plug and press, or use pliers

until contact is flush with plug. Repeat with other contact

(see illustra

tion).

4. T

wist wires sideways, insert into notch in plug and twist back

straight.

5. Snap plug on cable.

6. Install lamp (18w max.)(not included).

1. Secure trim (not included) to fixture housing by inserting

hooks on trim into two of the four slots in fixture housing and

twist clockwise until trim snaps in place. Bend hooks up

slightly (max. 1/8”) if trim is too hard to turn and lock into

position on housing.

WARNING: Use of other manufacturers components

will void warranty, U.L. listing and create a

potential safety hazard.

2 3/4”

NOTCH

CONTACT

*FUSED

PLUG

9488

*CABLE

*TRACK

FIXTURE WIRE

U.S. PATENT #5,465,199

FIG. 1

*FUSED

PLUG

9488

*NOT INCLUDED

FIXTURE

WIRE

RISK OF FIRE: DO NOT REMOVE REFLECT

OR.

CAUTION RISK OF FIRE. 12V LAMPS MUST NOT BE USED IN

24V SYS

TEM. INSTALL CABLE SO THA

CAUTION PRINTED ON CABLE IS VISIBLE

AFTER

INSTALLATION AND ATT

ACH THE 24V CAUTION LABELS (SUPPLIED

WITH THE 24V TRANSFORMER) ON OR

ALONG THE TRACK EVER

4 FT

1 2

FOR YOUR SAFETY 1

Summary of Contents

Page 1 - FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU AREWORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED OR THECIRCUIT BREAKER OFF.RISK OF FIRE: Exceeding

Page 2

FINAL INSTALLATION AND FUSING HC-207There are several ways to install the 9485 (disk-lights) using the 9774, 18w, 12V xenon lamps(actual consumption =

Comments to this Manuals

No comments

Sea gull lighting 9858-962 Installation Guide

Browse online or download Installation Guide for Unknown Sea gull lighting 9858-962. Sea Gull Lighting 9858-962 Installation Guide User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Sea gull lighting 9858-962