Sea gull lighting 4702-962 Installation Guide download pdf (Page 2)

Position faceplate (F) or decorative front (E) over sockets (J).

NOTE:

If backplate (C) is supplied with mounting studs (H) position

faceplate over studs and secure in place with cap nuts (G).

For fixtures supplied with cups:

Push faceplate (F) or decorative front (E) to wall and secure by

pushing cups (I) onto sockets (J) in a clockwise motion. (If your

fixture is supplied with threaded sockets, thread rings (L) onto

sockets (J) in the same manner except screw them on.) NOTE: If

both decorative front (E) and faceplate (F) are supplied, place

faceplate (F) and wood (or mirror), in that order, over sockets (J)

before securing with cups or rings (L). NOTE: It may be necessary

to bend tabs in cup (I) for a tighter fit.

GROUNDING INSTRUCTIONS: The green grounding screw (A) is to

be inserted into the hole with two raised dimples provided on the

back plate (C). Wrap the ground wire from the fixture (if supplied)

and the ground wire from the outlet box (bare metal or green insulat-

ed wire) around the green grounding screw (A) on the back

plate (C).

NOTE:

Underwriters Laboratories (U.L.) does not require all fixtures

to have ground wires. These fixtures still meet all U.L. specifications.

The listing mark of Underwriters on the product identifies products

manufactured under its listing and Follow-Up Service Programs.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

CLEANING

ORDERING PARTS

To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.

Do not use abrasive materials such as scouring pads or powders,

steel wool or abrasive paper.

Keep this sheet for future reference, and in case you need to order

replacement parts. All parts for this fixture can be ordered from place

of purchase. Be sure to use exact wording from illustration when

ordering parts.

GROUP A: CONNECT TO BLACK

HOUSE WIRE

BLACK

WHITE

*PARALLEL WIRE (ROUND & SMOOTH)

WHITE OR GREY WITH TRACER

BROWN, GOLD OR BLACK WITHOUT

TRACER

BROWN, GOLD OR BLACK WITH TRACER

WHITE OR GREY WITHOUT TRACER

*PARALLEL WIRE (SQUARE & RIDGED)

GROUP B: CONNECT TO WHITE

HOUSE WIRE

*NOTE: When parallel wire is used, the tracer wire is square shaped

or ridged, and the less tracer wire is round in shape or smooth. (Seen

best when viewed from wire end.) To separate wires, grasp the ends

of each wire and pull apart.

INSTALLATION TO AN OUTLET BOX (Fig. 1)

FINAL ASSEMBLY

STEP 1:

STEP 4:

STEP 1:

STEP 2:

STEP 3:

Install lamps

STEP 4:

STEP 2:

STEP 3:

Punch out appropriate holes in backplate (C), if applicable, to

correspond with holes in outlet box.

Tuck wires into outlet box. Attach backplate (C) to outlet box by

placing outlet box screws (not supplied) through punched out holes

in backplate (C).

If applicable:

Wood screws (K) placed in outer holes will provide

additional support.

Note:

Your fixture may be supplied with a faceplate (F), decorative

front (E), or both, depending on your model. Follow the directions

below according to the parts supplied with your fixture.

Make sure no bare wires can be seen outside wire connectors.

A. Take note of the color of the wire(S) on your fixture. Identify

which group your fixture wire(S) falls into and connect the wires

according to the directions below:

B. Take your fixture wire(S) from group A and place evenly

against the black wire from the outlet box. Do Not twist wires

together before using wire connectors.

C. Fit a wire connector (not supplied) over the wires and screw

the connector clockwise until you feel a firmness.

D. Try gently to pull the connector off the wires. If you can pull

the connector off, carefully re-do steps B and C, as above, and

check again for a firm connection.

E. Connect the fixture wire from group B to the white wire from

the outlet box in the same manner.

Push socket wires thru plastic bushing.

Note:

Fixtures that employ a grounded type receptacle are not

intended for connection to a two wire ungrounded source of supply.

THIS FIXTURE CAN BE MOUNTED TO A WALL WITHOUT AN

OUTLET BOX, MAKING THE WIRING CONNECTION BETWEEN

THE FACEPLATE AND BACKPLATE.

1. Remove knock-out from the backplate (if applicable), or remove

plastic bushing.

2. Install Romex / Bx connector on the backplate.

3. Feed house supply wires through Romex / Bx connector, and

secure.

4. Make wiring connection as described in the steps that follow,

and tuck the wires between the faceplate and backplate.

ALTERNATIVE MOUNTING METHOD (Fig. 2) HC-107

1 2

Comments to this Manuals

No comments

Sea gull lighting 4702-962 Installation Guide Page 2

Comments to this Manuals

Related products and manuals for Unknown Sea gull lighting 4702-962