Install lamps.
Raise diffuser (H) and decorative cap (L) to canopy so that center
pipe (G) protrudes through hole in decorative cap (I). Secure in
place with finial (J).
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated ground wire is on the mounting bar,
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied) (See Figure 2).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products manu-
factured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
CLEANING
ORDERING P
ARTS
T
o clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper
.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
WHITE
*
PARALLEL WIRE (ROUND & SMOOTH)
WHITE OR GREY WITH TRACER
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
WHITE OR GREY WITHOUT TRACER
*PARALLEL WIRE (SQUARE & RIDGED)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.)
T
o separate wires, grasp the ends
of each wire and pull apart.
INSTALLATION
FINAL ASSEMBLY
STEP 1:
STEP 4:
STEP 1:
STEP 2:
STEP
3:
STEP 2:
STEP 3:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Raised side is top as illustrated.
After wires are connected, tuck them carefully inside outlet box.
Raise the canopy (E) to the ceiling allowing for mounting screws (I)
to protrude through key slots (N). Rotate canopy (E) clockwise until
screws (I) are in narrow part of keyslot (N). Tighten screws (I) with
screwdriver.
Make sure no bare wires can be seen outside wire connectors.
Thread fixture mounting screws (I) into threaded holes of mounting
b
ar (A) 3 turns each.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
A.
Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box.
Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E
.
C
onnect the fixture wire from group B to the white wire from
the outlet box in the same manner.
ASSEMBLY HC-644
C
arefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
a
ny of the screws or parts which are needed to install this fixture.
(2 pages)
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals