Sea gull lighting 6150-44 Installation Guide Page 2

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 1
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
WHITE
*
PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
INSTALLATION HC-838
STEP 1:
STEP 2:
STEP 3:
WIRING
Insert fixture mounting screws (I) in threaded holes of offset
strap (C). Run screws all the way down to the heads.
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
Place flat strap (B) of mounting bar against outlet box (not supplied)
and fasten mounting bar, through slots in flat strap (B), to outlet box
with outlet box screws (K) (not supplied). Be sure the mounting
screws are perfectly horizontal so fixture hangs straight.
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
Hold mounting bar with flat strap (B) behind offset strap (C). Rotate
straps so they are at right angles to one another.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box.
DO NOT twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
FINAL ASSEMBLY
STEP 2:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar. Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (D) on the mounting bar.
If uninsulated wire is on the mounting bar, connect the ground wire
from the fixture (if supplied) and the outlet box to it using a small
wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
ORDERING PARTS
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and then
raise the canopy (G) against ceiling allowing for mounting screws (I) to
protrude through holes in canopy (G). Secure in place with cap nuts (F).
STEP 2:
Install lamp.
STEP 3:
Raise glass (N) to fixture body and secure with retaining screws (P).
STEP 4:
Install guards (Z) to fixture body.
Make sure no bare wires can be seen outside wire connectors.
FOR STEM MOUNT AND CHAIN HUNG
FOR CHAIN HUNG ONLY
STEP 1:
Using 2 pair of pliers, open one link of chain (Y) and connect it to the
fixture loop (X) at the top of the fixture.
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 1:
Lace fixture wire up through entire chain (Y) and pass through
canopy loop (S). We recommend lacing wire up through every
other link of chain (Y).
STEP 2:
FOR STEM MOUNT AND CHAIN HUNG
Lamp Information
Socket Ballast
LAMP
• Push Lamp into socket.
Do not twist.
*NOTE:
* For Solid Copper
Fixtures*
Use a good quality
automotive wax at
least twice a year to
protect your fixture. If
this additional care is
not taken, your fix-
ture will turn into a
Patina Finish over
time.
Page view 1
1 2

Comments to this Manuals

No comments